Currently in stock we have a large selection of products such as single end screwdriver bits, double end screwdriver bits, ratchet screwdrivers, screwdriver bits kit, and multiple other accessories for power tools. Coming, Meeng Gang continues to release new products. The newly arrived tools includes: precision HSS screwdriver, floating screwdriver, super extended torsion bit, power screwdriver bits kit, smart clutch setter, etc.

Our partners at Merlin and Ralter have been successfully l...

The electric power meters are used to measure the amount of electricity consumed by any type of electrical device. These meters use measurements in watts, volts, and amps to provide useful feedback when dealing with any type of electrical problem.

Electric power meters serve residential measurement across the widest possible range. Several specific meter families include electricity meters, ranging from the simplest and the most cost-effective to sophisticated devices, having many intern...

The electric power meter keeps track of the number of kilowatt-hours of electricity you use. Each month, a MINSUN Technology representative reads the meter to determine how much electricity you have used since the last reading. Your monthly bill is based on this meter reading.

The electricity you buy from MINSUN Technology is measured in kilowatt-hours. A kilowatt equals 1,000 watts, and a kilowatt-hour is 1,000 watts used for one hour. As an example, ten 100-watt light bulbs left on for ...

Industrial Ethernet connectors combine existing waterproof RJ connector technology with an efficient mini circular design. Threaded outer connection contributes to: Environmental sealing (IP67 rated), vibration resistance and secure, robust connections.

The waterproof RJ45 system provides assurance that dust or water will not interfere with signal integrity. They include two sub-families: the low-voltage system, which is rated up to 125 volts; and the high-voltage system, rated up to 250 vol...

The waterproof power connector is a device providing electrical power to many applications such as power usage of PV inverter and outdoor lamp. This equipment consists of the miniature 400 Series, mini, 6000 series, standard, 7000 Series and the 900 Series. Screw terminations ensure simple ‘field’ connection, whilst crimp terminations fulfill the requirement for fast effective volume connections.

Each range has flex cable connector, in-line flex cable connector and panel mounting connec...

The normal way to have a hi-quality audio speaker kit cannot without a high grade bi-wire cable. The cable is to use a number of individually insulated conductors within the cable construction. This method is utilised to great effect in the design of loudspeaker bi-wire cables. However, this results in a product that has a very high quality sound performance, but is expensive to manufacture and can be difficult to terminate. 

To take advantage of this design ethos, but in a more conventional...

There are several common methods out there for powering LED's. Why all the fuss? It boils down to this:1) LED's are very sensitive to the voltage used to power them (ie, the current changes a lot with a small change in voltage)2) The required voltage changes a bit when the power LED driver is put in hot or cold air, and also depending on the color of the LED, and manufacturing details. So there's several common ways that LED's are usually powered, and i'll go over each one in the following st...

On linear power supplies, the switch mode power supply is set to deliver its maximum power, even if the circuit that is connected to it isn’t pulling a lot of current. The result is that all components are working at their full capacity, even if it isn’t necessary. The result is the generation of a greater heat.

The main advantage of this method is greater efficiency because the switching transistor dissipates little power when it is outside of its active region (i.e., when the transisto...

A switch mode power supply designed for AC input can usually be run from a DC supply, because the DC would pass through the rectifier unchanged. If the power supply is designed for 115 VAC and has no voltage selector switch, the required DC voltage would be 163 VDC (115 × √2). This type of use may be harmful to the rectifier stage, however, as it will only use half of diodes in the rectifier for the full load. This could possibly result in overheating of these components, causing them to f...

In today's fast-paced workplace maximizing productivity is essential. Whether installing new fiber links or troubleshooting an existing network, the faster you can locate a problem, the faster you can fix it. That's easier said than done when you are faced with a complex network of fibers, connectors and patch cords. You can diagnose and repair simple fiber link problems with Visual Fault Locator (VFL). The laser-powered visual fault locator locates fibers, verifies continuity and polarity, a...

When you deploy Voice over IP (VoIP) or Gigabit Ethernet, you want to make sure that the existing cabling will support the bandwidth requirements of your new equipment. Ethernet cable tester is an essential tool for you. Your cabling was certified, but moves adds and changes have rendered many links incapable of running desired speeds. Ethernet cable tester can quickly reveals whether a link, including patch cords, is qualified for voice, 10/100BASE-T, VoIP, or Gig. Knowing your cabling's ban...

The contents of this site are not meant to mislead. Specifications and review comments, along with their links, are meant for information purposes only and everyone is advised to research any product that interests them by reading reviews, manufacturers websites and literature.

A variety of connection options are available for your downstream connection such as the mini plug, RCA, XLR and a whole host of others. Moon Audio custom builds these in house by hand each day to your connection ...

       Blending powders is one of the oldest unit-operations in the solids handling industries. For many decades powder blending has been used just to homogenise bulk materials. Many different powder mixer machines have been designed in order to be able to handle materials with various bulk solids properties. On the basis of the practical experience gained with these different machines, engineering knowledge has been developed to construct reliable equipment and to predict scale-up and mixing...